Videos
เครื่องขยายเสียง Dynacord IPX10:4 4-Ch DSP Power Amplifier
เพาเวอร์แอมป์ Dynacord IPX10:4 แบบ 4 ชาแนล มีกำลังขับ 4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply, 70/100/140/200V and Low Impedance Modes, Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
ราคาสินค้าไม่รวมภาษีมูลค่าเพิ่ม
฿470,100.00
Description
Dynacord IPX10:4 4-Ch DSP Power Amplifier (4 x 2500W)
เพาเวอร์แอมป์ Dynacord IPX10:4 แบบ 4 ชาแนล มีกำลังขับ 4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply, 70/100/140/200V and Low Impedance Modes, Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
IPX series multi-channel power amplifiers mark the new, unprecedented standard for sound system amplification in mid to large-sized permanent installations. Our new high-performance amplifiers offer seemingly unlimited power and pristine audio quality.
Are featuring OMNEO IP networking architecture and groundbreaking audio performance. They embody several proprietary amplifier technologies developed by Dynacord engineering, one of the most experienced R&D teams in the audio industry.
Features:
- 4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply.
- Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive.
- Dante and OCA integration via OMNEO with fallback options.
- Parallel, bridged and parallel-bridged drive modes with 70/100V/140V/200V and low impedance operation
- High efficiency ecoRAIL technology for lower operating costs
Specifications
| OUTPUT POWER | ||||
| Low-Z mode: Load Impedance | 2 Ω | 2.7 Ω | 4 Ω | 8 Ω |
| Maximum Output Power1 | ||||
| Normal Mode, all channels driven | 2600 W | 3000 W | 2500 W | 1250 W |
| Bridge | – | – | 5200 W | 5000 W |
| Parallel | 5000 W | 4000 W | 2500 W | 1250 W |
| Parallel-Bridge | 10400 W | 12000 W | 10000 W | 5000 W |
| Direct Drive Mode: Nominal Voltage | 70 V | 100 V | 140 V2 | 200 V2 |
| Maximum Output Power1 | 2500 W | 2500 W | 5000 W | 5000 W |
| Number of Amplifier Channels | 4 | |||
| Maximum Output Voltage, Normal mode, per channel | 150 Vpeak | |||
| Maximum Output Current, Normal mode, per channel | 53 Apeak | |||
| AMPLIFIER | ||||
| Voltage Gain | ||||
| Low-Z mode, ref.1kHz | 32.0 dB, adjustable 20.0-44.0 Db | |||
| Direct Drive mode | 33.2/36.2/39.2/42.2 dB for 70/100/140/200 V | |||
| Input Sensitivity | ||||
| Low-Z mode, Max. Output Voltage | 10.7 dBu (2.66 V), adjustable -1.3-22.7 dBu | |||
| Direct Drive mode | 6 dBu (1.55 V), fixed | |||
| THD3 dB below max, AES17, 1 kHz | < 0.05 % | |||
| DIM 1003.15 kHz, 15 kHz | < 0.15 % | |||
| IMD-SMPTE60 Hz, 7 kHz | < 0.05 % | |||
| Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ω | < -80 dB | |||
| Frequency Responseref. 1 kHz, analog into speaker out | 20 Hz to 20 kHz (±0.5 dB) | |||
| Damping Factor 20 Hz to 200 Hz, 8Ω | > 400 | |||
| Output Stage Topology | Class D, fixed frequency | |||
| Signal to Noise Ratio Amplifier | ||||
| A-weighted, analog input | 112 dB | |||
| A-weighted, digital input | 115 dB | |||
| Output Noise | ||||
| A-weighted, analog input | < -70 dBu | |||
| A-weighted, digital input | < -73 dBu | |||
| CONNECTIVITY | ||||
| Analog Audio Input/Thru | ||||
| Type | 2 x 6-pin Euroblock, male | |||
| Maximum Input Level | +21 dBu | |||
| Input Impedance, active balanced | 20 kΩ | |||
| Reference level equal to digital input | +21 dBu for 0 dBFS | |||
| Speaker Output | 1 x 8-pin Euroblock, 6 mm, female | |||
| GENERAL | ||||
| Power Consumption | ||||
| Rated power consumption (see BTU table) | 1200 W | |||
| ⅛ Maximum Output Power at 4 Ω | 1765 W | |||
| Idle Mode (no input signal) | 80 W | |||
| Standby Mode | < 16 W | |||
| Dimensions (W x H x D), mm | 483 x 88.1 x 514.2 | |||
| Weight | 15.0 kg (33.0 lb) | |||
| Shipping Weight | 17.2 kg (37.8 lb) | |||
| DIGITAL SIGNAL PROCESSING | ||||
| Sampling rate | 48 kHz/96 kHz, OMNEO/Dante synchronized | |||
| Signal delay/latency Analog In to Speaker Out, 48 kHz/96kHz | 0.70 ms/0.53 ms | |||
| Dante Network Latency | typ. 1.00 ms | |||
| Signal Processing | ||||
| User EQ | 12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass,Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type | |||
| User Delay | 0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet) | |||
| Array EQ | 5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass | |||
| Array Delay | 0 to 500 ms per channel (units: μs, ms, s, cm,m, inches, feet) | |||
| Speaker EQ | 10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass & All-Pass | |||
| Speaker X-Over | Hi-Pass, & Lo-Pass per channel,6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel | |||
| Speaker FIR | Up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over | |||
| Speaker Limiters | Peak Anticipation Limiter & RMS/TEMP Limiterper channel | |||
| Other Functions | Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Pilot Tone Generator & Detection, Level Meters, Impedance Measurement & Load Monitoring | |||
| Memory | ||||
| DSP Presets | 1 Factory + 20 User | |||
| Speaker-Pool Presets | 30 Speaker Settings | |||
| Source Supervision & Fallback | Pilot Tone supervision at Analog & OMNEO/Dante inputs, switch over to alternative Source Selection | |||
| CONNECTIVITY | ||||
| Network | ||||
| Type | 2 x Neutrik EtherCON/RJ45, redundant PRIMARY/SECONDARY | |||
| General | 1000base-T/100base-TX, integrated switch | |||
| Network Audio Inputs | 8 channels, 48/96 kHz, OMNEO/Dante format | |||
| Network Audio Outputs (Monitor) | 2 channels, 48/96 kHz, OMNEO/Dante format | |||
| Mains Input | 1 x Neutrik powerCON-HC | |||
| GPIO Control Port | ||||
| Type | 1 x 8-pin Euroblock, male | |||
| Ports & Operating Modes | 3 x GPIO, switchable Analog In/Digital In/Digital Out | |||
| Analog Input Range | 0 V to +13 V, 40 kΩ input resistance | |||
| Digital Input Limits | ON: < 1.5 VOFF: > 2.0 V, internal Pull Up (10 kΩ) | |||
| Digital Outputs | ON: Output switched to GND, max. 200 mA OFF: Open Collector (40 kΩ to GND) | |||
| Reference Voltage Output | +10 V, max. 200 mA, supervised, short circuit protected | |||
| READY/FAULT contact | Galvanic isolated relay, max. 30 VDC/500mADC | |||
| GENERAL | ||||
| User Interface | ||||
| Display | Black/white OLED 256 x 64 pixel | |||
| Front panel indicators | 4 x status LEDs (POWER, STANDBY, FAULT, OMNEO) | |||
| Front panel operating elements | 3 buttons (UP, ENTER, DOWN) | |||
| Rear panel indicators | 1 x status LED (STATUS) | |||
| Rear panel operating elements | Mains Switch | |||
| Power Requirements | 100 V to 240 V, 50 Hz to 60 Hz AC | |||
| Power Supply Topology | Switching Mode Power Supply with digital controlledPower Factor Correction | |||
| Protections | Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over-/Undervoltage Protection | |||
| Cooling | Front-to-rear, temperature controlled fans, supervised | |||
| Ambient Temperature Limits | +5 °C to +40 °C (+40 °F to +105 °F) | |||
| IEC Protection Class | Class I (grounded) | |||
| Electromagnetical Environment | E1, E2, E3 | |||
| Color | Black | |||
| Amplifier at rated conditions, Low-Z Normal operation mode, all channels driven, 4 Ω loads, Analog input, 32dB Gain, 48 kHz sample rate, unless otherwise specified. 1Test signal for max. output power according IHFA-202 (Dynamic-Headroom, burst 1 kHz/20 ms on/480ms off/low level -20 dB). 2Available in Bridge operation mode only. |
||||
Related Products
